CrazyPilot64
New member
I tried all my USB2 and USB3 ports. No reaction. No error on device manager.
Controller is well connected (orange light)
Controller is well connected (orange light)
Open and run Real Flight. Under 'Simulation' go to 'Select Controller' Left click and display will appear on the screen. Click the 'Profile' and the options will display. scroll through the available options and select your choice. After selecting, you may have to hit the refresh button. You can use the 'Edit' and 'Calibrate' buttons to go to the screens. this should allow you to configure the controller to your preference.I tried all my USB2 and USB3 ports. No reaction. No error on device manager.
Controller is well connected (orange light)
I simply plug mine into a USB port on the front of the computer case and it works fine.As I understand it from past threads, the interlink dx is a high current device. A powered hub that does not rely on power from the mother board exclusively will likely be the solution.
I am new to the Realflight 9.5 and I ordered it with the DXs I'm not sure I got what I thought I was getting. It connects with usb great but I just read some of the posts and my question before I read them was I thought I would be able to put in like dual rates an like set up the throttle/flaps/elevator pitch settings for flaps or go around but I'm thinking that I will not be able to do in the DXs. I then thought ok I'll use my own controller the DX6 which is not exactly new but then in reading the posts it seems using this controller is a headache to get the switches to work what you what it to?????? but I thought I would be able to se the dual rates and flap/elevator throttle mix so I don't have to deal with the pitch ups. But maybe there is a way and I just have missed it.
I assume the DX controller is not the DXs controller as there are no push controls or sliders and limited switches?
If there is a way to do mixes could someone point me in the right direction.
Thanks
Sterk03
the dual rates, mixes, and expos are all handle by RF internally on a plane-by-plane basis. they can be set up and tweaked in the plane editor. the editor is powerful once mastered but can be daunting to learn. dual rates and expos are done 99.999% of the time in the radio tab. simple mixes can be done in the radio or electronics tab by adding a second input in a specific output channel or a mixer in the electronics tab.
the DX6 + a dongle or a cable can do human interface for rf, but it has the capability to the mixing that rf handles natively and rf needs to be told which channels do what as each company has the own special sauce for reversing and channel mapping
the interlink-DX is a human interface device for a computer, switch and button but no "brains" to do mixing, dual rates, or expo as rf handles that internally
View attachment 127950
View attachment 127951
View attachment 127952
View attachment 127953
@legoman Thank you for your post. I have questions similar to @sterk03 and your response helped a lot. The RF9.5S manual talks about the RF software programming but does not explain how to modify the settings. That said, I still have two questions:the dual rates, mixes, and expos are all handle by RF internally on a plane-by-plane basis. they can be set up and tweaked in the plane editor. the editor is powerful once mastered but can be daunting to learn. dual rates and expos are done 99.999% of the time in the radio tab. simple mixes can be done in the radio or electronics tab by adding a second input in a specific output channel or a mixer in the electronics tab.
the DX6 + a dongle or a cable can do human interface for rf, but it has the capability to the mixing that rf handles natively and rf needs to be told which channels do what as each company has the own special sauce for reversing and channel mapping
the interlink-DX is a human interface device for a computer, switch and button but no "brains" to do mixing, dual rates, or expo as rf handles that internally
View attachment 127950
View attachment 127951
View attachment 127952
View attachment 127953
@legoman Thank you for your post. I have questions similar to @sterk03 and your response helped a lot. The RF9.5S manual talks about the RF software programming but does not explain how to modify the settings. That said, I still have two questions:
1. some planes have "mixers" in the electronics section and some do not. Do you think it correct to assume that for those without mixers that one is basically out of luck in adding flap:elevator mixing? For example, the Viper 70 blooms with flaps but has no mixer. I assume I will just have to live with the blooming?
2. I want all rates on one switch. The configuration model for the Spektrum Interlink DX wants to put rates on three different switches. Would this be where I would use the electronics tab for additional inputs? I have not had much luck with this yet but I am still somewhat confused by the approach.
Thank you.
@legoman Thank you. I had been using the interlink-x controller with RF9 and 9.5S but decided to upgrade to RF Evolution and wanted the controller to mimic my actual RC transmitters (DX8 Gen 2, IX12). Now I'm frustrated as it seems like a step backwards...the other question "I want all rates on one switch. " I think they are already set up on one switch. I only use the interlink-x (not DX) so maybe that is why I see them on one switch not three.