Project: T-Rex 700E

[oneeyejack]

Currently I'm very busy!

Soon as I find some free time I'm drawing the T-rex 700E.
Here is the result of three weeks of work ...

 

[Mikeymike21]

YES! Thank you Jack!

If you would like pictures of the new flybarless version V2 I have it along with another Trex 700E Flybar model.

Those are mine in the picture below.

 

[Maj. Numbskully]

And not a Swiss Cross anywhere in sight ! ......I'm shocked mikey!

 

[oneeyejack]

If you would like pictures of the new flybarless version V2 I have it along with another Trex 700E Flybar model.

Hi mikey!

To draw the "T-Rex 700E" I'm using your photos from the link: https://forums.realflight.com/showthread.php?t=27072&highlight=t-rex

I need more (FLAT) photos, if possible: left, front & top.

suggestion:
Without the "ruler" I spent more time for the right size (millimeters)!

No ruler = more time = very late post

 

[Mikeymike21]

Ok I will take some photos in a few hours when i get up. I only have the flybarless version with me, I wont be able to get pictures of the flybar model until friday.

 

[oneeyejack]

Ok I will take some photos in a few hours when i get up. I only have the flybarless version with me, I wont be able to get pictures of the flybar model until friday.

OK, no problem I'll see you Friday!

As I said before I'm very busy and the T-rex is so complex and detailed, so it takes much longer.
JACKPOT! I have to reduce the details. TILL NOW it takes 8.000 polyssssssssss! SORRY!

 

[Mikeymike21]

I could not get any photos today, it was cloudy and the photos came out too dark.

I'll post them when the lighting is better.


Do you need any other photos?

 

[oneeyejack]

Do you need any other photos?

Hi

I need canopy 3-View (front, left & top). Shoot the foto more "flat" possible.

I can't define the (inside) measure between two main frames. See picture below (red arrow)...

Thanks

 

[Mikeymike21]

Ok i'll try ang get those for you.

Heres part of a canopy someone has done in vector, not sure if it will be useful but it does capture the side profile very well.

 

[oneeyejack]

Heres part of a canopy someone has done in vector, not sure if it will be useful but it does capture the side profile very well.

The picture is quite good, but lacks the right part of the canopy.

I need something like that, even in the best light and resolution. I hope that Friday... you will do the photos on your canopy.

See pictures ...

 

[Mikeymike21]

Ok i'll try and get a few like that.

Its raining today so no photos, I was only able to stay out for a few minutes before my heli started to get very wet.

 

[Mikeymike21]

Here are some more, still wont be able to get measurements until friday. Lighting is still very bad..

 

[oneeyejack]

The canopy is OK! As soon as I get time I begin to work.
Next step is flybarless main rotor.

 

[Mikeymike21]

I will take pictures with the head off the helicopter and photoshop measurements in.

 

[oneeyejack]

I will take pictures with the head off the helicopter and photoshop measurements in.

OK...

 

[jcsites]

hi

thank you so much

 

[Mikeymike21]

The headblock is 71.22mm tall, 53.67mm wide

Each blade grip is 72.76mm long, 30.54mm tall

Main blade grip arm is 20.25mm long

Both top and bottom washout arms are 60.23mm long

Flybar cage is 65.67mm wide, 76.11mm long

Swash plate is 40mm wide


The frames are 60.80mm wide

Motor is 50.22mm wide

Main shaft bearing blocks are 28.22mm long, 60mm wide

The measurement between the top of the bearing block and the top of the head is 147.51mm

Thats all of the measurements for the head. I will give more later, i have to visit a helicopter fun fly in a few hours.

Thank you

 

[oneeyejack]

Thats all of the measurements for the head...
Thank you

I'm working on measurements...

BTW... how about the measure of the "Flybarless Main Rotor"?

Thanks

 

[Mikeymike21]

I will get you those measurements when i can. The only difference in size is the headblock height, the width and blade grip length is the same as the flybar version.

 

[oneeyejack]

Progress...